ENGINE RUN UP CFM56 | i-quiz.vn@stop article@stop ENGINE RUN UP CFM56 | i-quiz.vn

ENGINE RUN UP CFM56

Image Exam
2026-11-18 14:41:56
Tên đề thi: ENGINE RUN UP CFM56
Số lượng câu hỏi: 29
Thời gian làm bài: 01:00:00
Số điểm tối thiểu để vượt qua đề thi: 75
Tổng số điểm của đề thi: 29
Số lượt thi: 7
Lệ phí thi: Miễn phí
Bảng xếp hạng
User avatar
Nguyen Viet Anh-VAECO
29
2026-11-18 16:08:48
i-quiz
i-quiz App
🚀 Mới ra mắt

Tạo đề thi, làm bài thi, theo dõi kết quả ngay trên điện thoại — mọi lúc mọi nơi!

Tải trên Google Play Tải trên App Store

Nội dung đề thi: ENGINE RUN UP CFM56

Xem trước 25/29 câu hỏi trong đề. Bấm Vào thi để làm bài trực tuyến, được chấm điểm và xem đáp án chi tiết.

Câu 1. During an aborted autostart, the EEC will automatically engage the starter at the necessary N2 rotor at speed below:

  • A. 10% N2.
  • B. 20 % N2.
  • C. None, you have to engage manual at speed below 10%.

Câu 2. During the engine wet crank sequence, the following dry crank sequence will normally be initiated:

  • A. After the reset of ECU and core speed is less than 10%.
  • B. When ENG MODE SELECTOR is set to NORMAL and core speed is less than 10%.
  • C. After the reset of ENG MAN START pushbutton and N1 speed is less than 10 %.

Câu 3. What should be done initially if the engine catches fire (tailpipe fire) when starting?

  • A. Turn off the fuel and continue engine rotation with the starter.
  • B. Continue starting attempt in order to blow out the fire.
  • C. Continue engine start rotation and discharge a fire extinguisher into the intake.

Câu 4. During Normal automatic start. Active Igniter (A or B) come on when:

  • A. 18% N2
  • B. 16% N2
  • C. 30 seconds.

Câu 5. The main reason for doing engine manual start mode is:

  • A. To control the starter valve and fuel HP valve independently as necessary.
  • B. To start the engine without the control of the ECU
  • C. To replace the unsuccessful automatic start mode

Câu 6. For thrust balance and prevention of A/C movement during engine Run up:

  • A. The single engine operation is allowed up to 85%N1.
  • B. The non tested engine must be operated at 60%N1.
  • C. If power is higher than 75%N1, the A/C must be immobilized by wheel chocks and parking brake.

Câu 7. The automatic start abort function is available when N2

  • A. hot start, hung start, stall
  • B. ignition failure, start valve failure, low oil pressure
  • C. ignition failure, hung start, low oil pressure.

Câu 8. The engine motoring (dry or wet) can be performed normally:

  • A. For a maximum of 4 consecutive cycles (each of 2 minutes with a 20 seconds rest between 2 cycles)
  • B. For a maximum of 4 consecutive cycles (3 of 2 minutes and 1 of 1 minute with a 20 seconds rest between 2 cycles)
  • C. For a maximum of 3 consecutive cycles (2 of 2 minutes and 1 of 1 minute with a 20 seconds rest between 2 cycles)

Câu 9. ECU is automatic decrease 7% fuel if:

  • A. There is engine stall.
  • B. Engine overtemp.
  • C. Both answer are correct

Câu 10. Which one below is true regarding the engine operation?

  • A. before the engine start and wet cranking, the extinguisher presence is required.
  • B. before the engine cranking, the extinguisher presence is required.
  • C. before the engine start and dry cranking, the extinguisher presence is required.

Câu 11. When doing wet motoring:

  • A. The fuel injection is not recommended for more 60 seconds
  • B. No time restriction for fuel injection
  • C. The fuel injection is not recommended for more 15 seconds

Câu 12. Which statement below is correct during manual start:

  • A. The starter valve can be closed by selecting manual start p/b “OFF” at any time prior to turning master switch “ON”
  • B. The starter valve can be closed by selecting manual start p/b “OFF” at any time
  • C. The starter valve can be closed only by ECU at 50% N2

Câu 13. To prevent the engine rotors from thermal stress and to minimize oil coking, before a normal shutdown:

  • A. Operates the engine at minimum idle for 15 minutes
  • B. Operates the engine at minimum idle for 5 minutes
  • C. Operates the engine at minimum idle for 3 minutes

Câu 14. For engine start and operation at Idle:

  • A. Maximum wind speed to the Tail is 10 knots.
  • B. Maximum wind speed to the Tail is 9 knots.
  • C. Not permit engine start when there is tailwind.

Câu 15. During engine start, Air starter valve is closed by ECU at:

  • A. 50% N1
  • B. 55% N1.
  • C. 50% N2.

Câu 16. Normal EGT limit for starting is:

  • A. 725 deg.C
  • B. 650 deg. C
  • C. 635 deg.C

Câu 17. Aircraft thrust balance during engine operation when do high power assurance test.

  • A. The N1 speed of non-tested engine must be equal 60% (N1 = 60%).
  • B. The N1 speed of nontested engine must be equal 70% (N1 = 70%).
  • C. The EPR of non-tested engine must be equal 1.08

Câu 18. When starting the engine, the starter should be disengaged automatically:

  • A. Only after the engine has reached full idle RPM.
  • B. When the ignition and fuel system are activated.
  • C. After the engine has reached self-accelerating speed ( 50%N2 ).

Câu 19. During engine start in manual mode, IGN A and B are shown on ECAM

  • A. It means that system A and B have failed
  • B. It means that one system has failed
  • C. This is normal.

Câu 20. If a fast EGT increase, followed by slow N2 acceleration occurs during manual start:

  • A. Monitor the engine’s other parameters, if they are in limits then continue the start sequence
  • B. Immediately abort the start
  • C. Continue the start sequence anyway.

Câu 21. The pressure for start:

  • A. Starter press 25-55 psig
  • B. Starter press 30-40 psig
  • C. None of above

Câu 22. EGT limit during engine start is:

  • A. 635 degC
  • B. 725 degC
  • C. 1083.33 degC

Câu 23. You must pull C/B to open fuel LP valve before:

  • A. wet motoring the engine
  • B. dry motoring the engine
  • C. starting the engine in manual mode

Câu 24. A hung start is indicated if the engine

  • A. RPM exceeds specified operating speed.
  • B. Exhaust gas temperature exceeds specified limits.
  • C. Fails to reach idle RPM.

Câu 25. Power assurance check is used to:

  • A. to make sure the engine will make rated thrust within the EGT, N1 and N2 speed limits when you set to target N1 power.
  • B. Check the oil pressure of supply line.
  • C. Check the vibration of the engine

… và còn 4 câu nữa. Bấm Vào thi phía trên để làm toàn bộ 29 câu và xem đáp án.

Bình luận
Thêm bình luận của bạn
Nội dung

0 Bình luận

Xem thêm bình luận trước đó